ERICSSON REDBACK NETWORKS SMARTEDGE 400 CHASSIS w/1*ENET10/100 1*XCRP3 1*ATM DS3

Description

TESTING & COSMETIC NOTES:
This is a USED WORKING item in GOOD cosmetic condition that WAS PULLED FROM A WORKING ENVIRONMENT and is GUARANTEED WORKING AS DESCRIBED
Unit fully powers up. We were able access this unit through the console terminal. See console log below for detail. Please note power supply and interconnect cable are NOT included.
COMPONENTS INCLUDED IN THIS AUCTION:
• (1) - REDBACK SMARTEDGE 400 CHASSIS IPM6Z00KRA
• (1) - REDBACK SMARTEDGE 400 ENET 10/100 MODULE SN4PCGECAA
• (1) - REDBACK SMARTEDGE 400 ATM DS3 MODULE SN03NNFDAA
• (1) - REDBACK SMARTEDGE 400 XCRP3 MODULE SOUIAKHUAA
• (1) - REDBACK SMARTEDGE 400 ALARM CARD IP2CY30JAA
• (1) - REDBACK SMARTEDGE 400 FAN MODULE IP2CX20JAA
REPLACEMENT GUARANTEE - ITEM IS GUARANTEED WORKING AS DESCRIBED:
Please see our test notes above for further information. Our descriptions, and photos represent our best effort to relay all pertinent information about a product. We assure the buyer that they will receive an item with the level of operation shown in the photos and described in our Test and Cosmetic notes. When you receive a Guaranteed item from OC Depot, it should perform as described. In the rare situation that this is not the case, we will send a replacement upon safe return of the original item within 30 days of receiving the item. If a replacement is not available we will honor the terms of our Money-Back Guarantee. We do not refund the shipping charges because we are unable to recoup these costs.
ADDITIONAL INFORMATION:
Software Feature License Configured
-------------------------- ------------------
subscriber high-availability YES
[0]Booting(2)....
Enabling L1/L2 Caches...
Reset Cause:
Power On Reset (PPC/TDM Subsystems)
Cold boot, clearing out vxWorks memory space
SCC RAM controller Initialized
PPC1: Initialized PPC1
Detected Peer XC-RP, will try to establish link....
PPC1: Polling for commands from PPC0
Monitor 0 channel 1 Voltage is 1.506 V (9A40)
Monitor 0 channel 2 Voltage is 1.779 V (B640)
Monitor 1 channel 1 Voltage is 5.048 V (8140)
Monitor 1 channel 2 Voltage is 3.314 V (A9C0)
Monitor 1 channel 3 Voltage is 2.548 V (8280)
Monitor 1 channel 4 Voltage is 2.111 V (D840)
Monitor 0 Temp = 21.50 C (1580)
Monitor 1 Temp = 23.00 C (1700)
System memory available is set from Entitlement Block
ATA device not present or not responding
Reading MAC address
Backplane EEPROM MAC address 00:30:88:01:9E:49
Welcome to SmartFirmware(tm) for Redback PowerPC Copyright (c) 1999-2003 by Redb
ack Networks, Inc. version 1.0b1267
SmartFirmware(tm) Copyright 1996-2000 by CodeGen, Inc.
All Rights Reserved.
Executing POST
PPC0 L2 Cache Test : PASSED
Sandisk Screen Test : PASSED
Bridge Test : PASSED
PPC SDRAM Test : PASSED
SCC SDRAM Test : PASSED
Serial(16552) Test : PASSED
Ethernet Test : PASSED
ISA Bridge Test : PASSED
Forte Test : PASSED
Opus Test : PASSED
Max Test : PASSED
Bits Test : PASSED
SCC Test : PASSED
Compact Flash Test : PASSED
PC Card Test : PASSED
POST PASSED
Auto-boot in 0 seconds - press se* to abort, ENTER to boot:
inflating image from 6914682 bytes to
Flushing L1 D-Cache, @ 0x10000, 48872540 bytes
PPC1: PPC1 image loaded
|
verifying checksum of /p02/netbsd ... succeeded
Flushing L1 D-cache, @ 0x5A00000, 2074686 bytes. Please wait....
Syncing L1-I cache, Please wait....
launching...
Please Click Here to Visit Our Store
SearchBy8 -
213141
| Loc: J42 | L: Rob | T: Morgan
| PM: Nick
| QTY: 0 | Plan: S- Q4 5 pounds or more | 21.00"x19.00"x12.00" 57.00lbs | Start: {{detail_product_description}}.00 | BIN: 9.98 |  | 6/26/2019 |
|
51279